If you are ready to choose a new best DRILL PRESS FOR METAL, check out our detailed recommendation below!.
10 Best DRILL PRESS FOR METAL
Best DRILL PRESS FOR METAL
WEN 4208 8 in. 5-Speed Drill Press
- Includes a 1/2-inch keyed chuck and onboard key storage
- Operates at 5 different speeds: 740, 1100, 1530, 2100, 3140 RPM
- Spindle travels up to 2 inches with easy to read, locking linear depth stops for accurate and repeatable drilling operations.Cord Length (ft.):6
- Durable 1/3 HP induction motor develops ample torque and power
- 6-1/2 x 6-1/2" worktable is height adjustable and bevels up to 45 degrees left & right
WEN 4214 12-Inch Variable Speed Drill Press,Orange
- Infinitely variable speed ranges from 580-3200 RPMS. Mechanical variable speed delivers equal torque throughout the range. LED read out displays speed.
- Spindle Travel of 3-1/8" with easy to read, locking linear depth stop for accurate and repeatable drilling operations. Front to the back of the motor is 22 inches
- Quill diameter of 2.17 inches. Durable 2/3hp induction motor develops ample torque and power. Motor: 120 V, 60 Hz. Laser Module: Class III
- 9-1/2 x 9-1/2" cast iron worktable features rack & pinion height adjustment and bevels up to 45 Degree left & right. Width with the handles: 14-1/2"
- Includes drill press, mechanical variable speed, laser, table roller extension, 5/8" keyed chuck & key, tools for assembly.Drill press Height from the Floor to the top: 37 inch
Drills and Drill Presses (Missing Shop Manual ): The Tool Information You Need at Your Fingertips
33 used from $2.37
- Used Book in Good Condition
The Drill Press (Build Your Own Metal Working Shop From Scrap Serie Book 5)
|Is Adult Product|
|Number Of Pages||168|
Milescraft 1318 Drillmate Drill Guide with chuck
- Perfect for straight or angled drilling, drilling on the edge of a board or on round stock
- Attaches to all 3/8" And 1/2" Power drills and it also includes a 3/8" Capacity chuck with key
- Angle cuts of 45 Degree to 90 degrees, with a built in angle read out in the all metal base
- Centering channels built into the bottom of the base, to accommodate drilling any round stock up to 3 inches in diameter
- Adjustable depth stop and spring action control of the head
SKIL 3320-01 3.2 Amp 10-Inch Drill Press
- 1/2-inch keyed chuck. Bump-off switch for added safety
- 5 speeds - 570 - 3,050 RPM
- Adjustable depth stop for accurate measurements and repetitive drilling
- 0-45 degree left/right tilting work surface
- Laser X2 2-beam laser for precise hole alignment
JET J-2500 15-Inch 3/4-Horsepower 115-Volt Floor Model Drill Press
- Work table tilts 45°.
- GREATER PRECISION AND ACCURACY: Enclosed spidle assembly is supported by four permanently-lubricated ball bearings.
- TELESCOPING SPINDLE GUARD: Extend the guard as much as needed.
- 3-1/8" stroke for deep hole applications.
- 5/8" drill chuck and arbor
Boneham Metal Products Inc. Headed Press-Fit Drill Bushing (H), Standard Wall, Headed, Letter, H - 1 Each
- United Kingdom
Drill Hog Silver & Deming Drill Bit Set 9/16" to 1" Drill Hog
- Hi-Molybdenum M7 Steel
- 9/16" to 1" with 1/2" Cut Down Shank
- 135 Degree Split Point Prevents "Walking"
- 3 Flat Sides on the Shank Prevents "Spinning"
- Lifetime Warranty